Crawfordville, FL HVAC Service

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Replaced the 20x20x5 pleated 2-6" filter in the attic air handler. * Confirmed the indoor coil is clean and in fair condition. * Inspected the blower wheel, primary drain pan, secured electrical wires, and ductwork; all are in good condition. * Cleared the condensate drain line, cleaned the primary pan, and tested the safety switch. **Outdoor Unit Service** * Confirmed the outdoor heat pump coil is clean and in fair condition. **Electrical System Check** * Tested the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. All are working within manufacturer specifications. **System Performance & General Maintenance** * Measured return air temperature at 72.0°F and supply air temperature at 53.0°F. * Dusted the thermostat, checked its batteries, and tested its operations. * Restored power to

Today I performed a routine maintenance on your HVAC equipment. I checked all electrical connections on both indoor and outdoor equipment, checked your air filter, flushed your drain line, check the capacitor ratings, and then make sure the system came on and was cooling properly before leaving. Your system is operating properly at this time. .

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Located the air handler in the closet. * Replaced the 19x20 Respicare filter with a customer-provided spare. * Confirmed the indoor coil is clean and in fair condition. * Inspected the blower wheel and confirmed it is in good condition. * Checked the primary drain pan and confirmed it is in good condition. * Tested the blower motor, which is working properly. * Measured return air temperature at 78.0°F and supply air temperature at 56.6°F. **Outdoor Unit Service** * Located the heat pump on the side of the house. * Confirmed the outdoor coil is clean and in fair condition. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, and contactor; all are working properly. **Drainage System** * Cleared the condensate drain line. * Cleaned out the primary drain pan. * Tested the safety switch. * Ensured the drain line is c

Opponent arrival I found the system not cooling properly due to it being off on a hard lockout for pressure. After further inspection, I found the air filter to be plugged. I pulled the air filter and swapped it out with a new one. I also found the water valve to be burning up hot. I believe the water valve is going out and is closing at times causing the system to not cool properly. I returned the morning of Thursday, July 2 to find the water valve for the water source unit to be bad and stuck closed, causing the system not to cool properly. I found the water valve to be bad. I sent an estimate to replace it. The estimate was approved. After installing the new water valve, I tested the system operations by turning it on and off at the thermostat the valve opened and closed with no leaks as it should. Your system is cooling properly at this time .

Today we performed a summer time tune up on your unit,everything is working properly at this time .Thank you for your business. Tallahassee FL View visual findings from this job here - https://visionshare.xoi.io/?id=XA-8440-498616FA919E40D6848FC6E2A3014439

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Inspected the air handler in the attic, garage. * Replaced the 20x25x5 filter. * Confirmed the indoor coil is clean and in fair condition. * Checked the blower motor, blower run capacitor, and electrical wiring; all are working properly. * Inspected the blower wheel, primary drain pan, secondary drain pan, and ductwork; all are in good condition. * Cleared the condensate drain line, cleaned the primary and secondary pans, and tested the safety switch. * Confirmed the drain line is strapped and secured. * Verified the UV light is on and shining. **Outdoor Unit Service** * Inspected the heat pump on the side of the house. * Confirmed the outdoor coil is clean and in fair condition. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, and contactor; all are working within specifications. **Syste

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Overall Equipment Condition** * Found the equipment in fair condition. **Indoor Unit Service** * Located the air handler in the closet. * Serviced the whole home unit. * Checked filtration; the 24x30x1 filter was in fair, clean condition. * Inspected the indoor coil; it was fair and clean. **Outdoor Unit Service** * Located the heat pump on the side of the house. * Inspected the outdoor coil; it was fair and clean. **Electrical Component Checks** * Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring. **System Component Inspections** * Inspected the blower wheel, primary drain pan, secured electrical wires, and ductwork; all were in good condition. **Temperature Readings** * Recorded a return air temperature of 74.0

Today I arrived on site to perform a summer tune-up on your system. **Indoor Unit Service (Air Handler)** * Located the Air Handler in the garage attic. * Checked and replaced the 20x20x5 pleated 2-6" filter. Provided additional filters as requested. * Inspected the indoor coil; it is clean and in good condition. * Inspected the blower wheel, ductwork, primary drain pan, and secondary drain pan; all are in good condition. * Tested the blower motor and blower run capacitor; both are working properly. * Recorded a return air temperature of 76.0°F and a supply air temperature of 56.0°F. **Outdoor Unit Service (Heat Pump)** * Located the Heat Pump on the side of the house. * Inspected the outdoor coil; it is clean and in good condition. * Tested the condenser fan motor, contactor, defrost control board, and electrical wiring; all are working properly. * Tested the compressor run capacitor; it is out of factory range and needs replacement. **Drainage System** * Clea

Today I arrived on site to perform a summer tune-up on your system. **Indoor Unit Service (AIR HANDLER)** * Located the AIR HANDLER in the attic closet. * Checked the pleated 1" filters (one 18x18x1, four 12x12x1). * Confirmed the indoor coil is clean and in good condition. * Inspected the blower wheel, ductwork, primary and secondary drain pans, and electrical wires; all are in good condition. **Outdoor Unit Service (CONDENSER)** * Located the CONDENSER (heat pump) on the side of the house. * Cleaned the outdoor coil; it is in good condition. **Electrical Component Checks** * Tested the blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, defrost control board, and electrical wiring. All are working properly within manufacturer specifications. **System Operations & Maintenance** * Cleared the condensate drain line, cleaned the primary and secondary drain pans, and tested the safety switch.

Today I arrived on site to perform a summer tune-up on your system. **Indoor Unit Service (AIR HANDLER)** * Located the AIR HANDLER in the attic closet. * Checked and replaced the 16x20x5 pleated 2-6" filter. * Inspected the indoor coil; it is clean and in good condition. * Confirmed the unit services the whole home. **Outdoor Unit Service (CONDENSER)** * Located the CONDENSER (heat pump) on the side of the house. * Inspected the outdoor coil; it is clean and in good condition. **Electrical Component Checks** * Tested and inspected the Blower Motor, Condenser Fan Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, Defrost Control Board, and Electrical Wiring. All are working properly within manufacturer specifications. **System Component Inspections** * Inspected the Blower Wheel, Ductwork, Electrical Wires Secured, Primary Drain Pan, and Secondary Drain Pan. All are in good condition. **Condensate Drain System Maint

Today I arrived on site to perform a summer tune-up on your whole home system. **Indoor Unit Service** * Located the indoor unit in the attic. * Checked the 18x18x1 pleated 1" filter; customer will replace it with their spare. * Inspected the indoor coil, noting its fair condition. * Tested the blower motor and blower run capacitor; both are working properly. * Inspected the blower wheel, secondary drain pan, primary drain pan, and electrical wires; all are in good condition. * Cleared the condensate drain line, cleaned the primary and secondary pans, and tested the safety switch. * Confirmed the drain line is connected and strapped. * Measured return air temperature at 68.0°F and supply air temperature at 50.0°F. **Outdoor Unit Service** * Located the outdoor unit on the side of the house. * Inspected the outdoor coil, noting its fair condition. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor

Today I arrived on site and performed a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Checked the Respicare filtration system. * Inspected the 20x23 filter. * Confirmed the indoor coil is in good condition. * Tested the blower run capacitor. * Inspected the secondary and primary drain pans. * Verified ductwork is in good condition. * Cleared the condensate drain line and tested the safety switch. * Confirmed the drain line is strapped. * Measured return air temperature at 70.0°F and supply air temperature at 52.0°F. **Outdoor Unit Service** * Noted the outdoor coil is in fair condition. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly. **General System Check** * Inspected electrical wires, ensuring they are secured. * Tested thermostat operations. * Restored power to the units. **Recommendations** * Rem

Today I arrived on site to perform maintenance on your INTERNATIONALCOMFORT system. Indoor Unit Service Inspected the package unit, noting its fair overall condition. Serviced the whole home system. Checked the pleated 1" filter. The customer declined new filters and will provide their own 12x20x1 filter. Inspected the indoor coil, noting its fair condition. Outdoor Unit Service Inspected the package unit located on the side of the house. https://visionshare.xoi.io/?id=ms97a048d9-d427-i265-ae9549c6b9f2-u0FD-0b5070721e4d View visual findings from this job here - https://visionshare.xoi.io/?id=XA-05B7-A716A837536C4B7BB1E72F81FB853848

Diagnostic/ system not cooling. Verified the blower motor is operating properly. Hooked up my gauges and found the system low on refrigerant. Added 1 pound of 410a to get the system cooling again. I performed an electronic leak search and found a leak at the evaporator coil. I will order a new evaporator coil and txv under warranty. Refrigerant is not covered under warranty please see attached estimate. When the parts come in the office will contact you to schedule the job. The system is cooling properly at this time. Amana Air Handler Model#AVPTC37C14BA Serial#1905021021. Amana Condensing Unit Model#ASZ140301KD Serial#1904435461 5/21/26 Today we replaced the evaporator coil and txv, pressure tested the system to 350psi for 20 minutes, pulled a deep vacuum under 500 microns and added refrigerant charge back to the unit to get it cooling properly. Tallahassee fl

Upon arrival, I found the customers split system, not cooling properly due to the thermostat being blank. After further inspecting the system, I found the drain line to be clogged, which was causing the safety float switch to kill the low-voltage power. I gave an estimate to flush the drain line. Estimate was approved. After flushing the drain line I tested the system operations and your system is cooling properly at this time .

Today I arrived on site to perform a summer maintenance on your HVAC equipment. Indoor Unit Service Checked the AIRHANDLER in the attic. Confirmed the indoor coil is clean and in good condition. Inspected the blower wheel, primary, and secondary drain pans; all are in good condition. Verified ductwork is in good condition and electrical wires are secured. Checked the 20x20x1 pleated 1" filter, which is in good condition. Outdoor Unit Service Inspected the CONDENSER (heat pump) on the side of the house. Confirmed the outdoor coil is clean and in good condition. Electrical Component Checks Tested the blower motor, condenser fan motor, compressor, and associated run and start capacitors. Verified the contactor and electrical wiring are working properly within manufacturer specifications. System Operations & Maintenance Cleared the condensate drain line and tested the safety switch. Confirmed the drain line is connected and strapped down. Measured return air temperature at 70.0°F and supp

Today I arrived on site and performed a summer maintenance on your HVAC equipment. Indoor Unit (AIRHANDLER) Located in the attic. Replaced the 20x20x4 pleated 2-6" filter. Inspected the indoor coil; condition is fair. Checked the blower wheel, primary drain pan, electrical wires, ductwork, and secondary drain pan; all are in good condition. Tested the blower motor and blower run capacitor; both are working properly. Measured return air temperature at 75.0°F and supply air temperature at 53.6°F. Outdoor Unit (CONDENSOR) Located on the side of the house. Inspected the outdoor coil; condition is fair. Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly. System Maintenance Cleared the condensate drain line and tested the safety switch. Confirmed the drain line is strapped and secured. Dusted the thermostat, checked its batteries, and tested its operations. Restored

Today I arrived on site and performed a summer maintenance on your HVAC equipment. Overall System Check Inspected the Package Unit, located on the side of the house. Confirmed the overall condition of the equipment is fair. Serviced the whole home area. Filtration and Coils Checked the 10x20x1 pleated 1" filter. Noted the indoor and outdoor coils are in fair condition. Electrical Component Testing Tested the Blower Motor, Condenser Fan Motor, Compressor, and all associated run and start capacitors. Verified the Contactor and Electrical Wiring are working within manufacturer specifications. Component Inspections Inspected the Blower Wheel, Primary Drain Pan, and Ductwork; all are in good condition. Confirmed electrical wires are secured. Performance and Maintenance Measured return air temperature at 76.0°F and supply air temperature at 53.9°F. Cleared the condensate drain line and ensured it is strapped down. Dusted the thermostat, checked its batteries, and tested its operations. Rest

Today I arrived on site and performed a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Inspected the indoor unit, located in the garage attic, and found its overall condition good. * Serviced both the East and West side areas of the unit. * Replaced the Respicare filter with a customer-provided spare, size 19x20. * Confirmed the indoor coil is in good condition. * Cleaned out the primary drain pan and cleared the drain line. * Tested the safety switch and confirmed the drain line is connected and strapped down. **Outdoor Unit Service** * Inspected the outdoor heat pump, located on the side of the house, and found its coil good and clean. **Electrical Component Check** * Tested and confirmed the following electrical components are working properly within manufacturer specifications: * Blower Motor * Condenser Fan Motor * Compressor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Electrical Wi

Today I arrived on site and performed a summer maintenance on your HVAC equipment. ### Indoor Unit Service (AHU) * Inspected the Air Handler in the garage attic. * Checked the whole home's area unit services. * Verified the 20x20x1 pleated 1" filter. * Cleared the condensate drain line and tested the safety switch. * Secured the drain line with a strap. * Inspected the primary and secondary drain pans; they are in good condition. * Tested the blower motor, blower run capacitor, and electrical wiring; all are working properly. * Measured return air temperature at 74.0°F and supply air temperature at 54.0°F. ### Outdoor Unit Service (CONDENSER) * Inspected the Heat Pump on the side of the house. * Cleaned the outdoor coil; its condition is fair. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly. ### General System Checks * Restored pow

Today we performed a summer time tune up on your unit,everything is working properly at this time .Thank you for your business. Tallahassee FL

Today we performed a summer time tune up on your unit,everything is working properly at this time .Thank you for your business. Tallahassee FL https://visionshare.xoi.io/?id=ms1ba6d7d2-302f-i262-c3c64a369e7e-uFB3-2f0d1337b341 View visual findings from this job here - https://visionshare.xoi.io/?id=XA-C335-315DC045D1C547A8B3907266CC70D924

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Inspected the air handler in the garage attic. * Confirmed the indoor coil is clean and in good condition. * Checked the 20x20x4 pleated filter; the customer will replace it. * Verified the blower wheel, primary drain pan, electrical wires, and ductwork are in good condition. **Outdoor Unit Service** * Inspected the heat pump on the side of the house. * Confirmed the outdoor coil is in good condition. **Electrical Component Checks** * Tested the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring. All are working within manufacturer specifications. **System Performance & Maintenance** * Measured return air temperature at 75.0°F and supply air temperature at 48.0°F. * Cleared the condensate drain line, cleaned the primary pan, and tested the safety switch. * E

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Replaced the pleated 1" filters (20x25x1 and 16x20x1) in the attic air handler. * Cleared the condensate drain line and cleaned out the primary pan. * Inspected the indoor coil, finding it in fair condition. * Checked the blower wheel, primary drain pan, secured electrical wires, and ductwork, all in good condition. **Outdoor Unit Service** * Inspected the heat pump's outdoor coil, finding it fair and clean. **Electrical Component Checks** * Tested the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring; all are working properly within manufacturer specifications. **System Performance & General Checks** * Measured return air temperature at 76.0°F and supply air temperature at 60.0°F. * Dusted the thermostat, checked its batteries, and tested its operations. * Restored power to the units.

Today I arrived on site and performed a summer tune-up. Here's a summary of the work completed: **Indoor Unit (Package Unit):** * Noted the overall equipment condition as fair. * Brush cleaned the indoor coil, which was in good condition. * Hosed down the evaporator coil. * Checked the antimicrobial filter; customer will provide their own replacement filters. **Outdoor Unit (Heat Pump, Package Unit):** * Noted the outdoor coil condition as fair and cleaned it. **Electrical Components:** * Tested and confirmed proper operation of the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. * Inspected and confirmed good condition of the blower wheel, secured electrical wires, primary drain pan, and secondary drain pan. **System Checks:** * Cleared the drain line and cleaned out the primary pan in the condensate drain system. * Measured a return air temperature of 75.0°F and a s