Bristol, FL

Today I arrived on site and performed a summer tune-up on the system. Here's a summary of the work completed: Indoor Unit (Air Handler):Verified the air handler is located in the closet. Confirmed the unit services the whole home. Replaced the pleated 1" filter (20x20x1). Confirmed the indoor coil is clean and in good condition. Outdoor Unit (Heat Pump):Verified the heat pump is located on the side of the house. Cleaned the outdoor coil; it's now in good condition. Electrical Components (Tested and Working):Blower Motor Condenser Fan Motor Compressor Compressor Run Capacitor Fan Run Capacitor Contactor Defrost Control Board Electrical Wiring Components Inspected (Good Condition):Blower Wheel Primary Drain Pan Electrical Wires Secured Condensate Drain System:Cleared the drain line. Cleaned out the primary pan. Tested the safety switch. Confirmed the drain line is strapped. Measurements:Return air temperature: 69.0°F. Supply air temperature: 50.0°F. Additional Actions:Dusted the return

Today I arrived on site and performed a winter tune-up on your system. Here's a summary of the work completed: Air Handler Service: Replaced the pleated 1" filter (2-20x20x1, 1-14x14x1). Confirmed the indoor coil is in good, clean condition. Verified the blower wheel, primary drain pan, and electrical wires are secured and in good condition. Cleared the condensate drain line, cleaned out the primary pan, and tested the safety switch. Condenser Service: Cleaned the outdoor coil, which is in good condition. Tested and inspected the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, electrical wiring, and defrost control board; all are working properly within the manufacturer's recommended specifications. Confirmed the drain line is strapped. Additional Checks: Return air temperature: 72.0 Degrees Fahrenheit. Supply air temperature: 118.0 Degrees Fahrenheit. Dusted the return grills and thermostat. Checked the batteri

Today I arrived on site and performed a summer time maintenance on your HVAC equipment. **Indoor Unit (Air Handler):** * Replaced the 20x25 pleated air filter. * Confirmed the indoor coil is clean and in good condition. * Verified the blower wheel, primary drain pan, and electrical wires are secured and in good condition. **Outdoor Unit (Heat Pump):** * Confirmed the outdoor coil is clean and in good condition. * Tested and inspected the blower motor, condenser fan motor, blower run capacitor, compressor run capacitor, compressor, contactor, and electrical wiring, all operating within manufacturer's specifications. **System Performance:** * Cleared the condensate drain line and tested the safety switch. * Measured a return air temperature of 70.0°F and a supply air temperature of 52.0°F. * Tested the thermostat operation and restored power to the units. View visual findings from today’s visit here - https://visionshare.xoi.io/?id=ms5e176931-4b40-i185-9a2b4fb99a

Today, I arrived on site to conduct a thorough inspection and tune-up of the HVAC system. Overall Equipment Condition The overall condition is fair. Indoor Unit Details Located in a closet, the air handler services the whole home. The pleated filter (2-20x20x1) was checked today. Outdoor Unit Details Located on the side of the house, the heat pump's outdoor coil is in good condition and was cleaned today. Electrical Components Blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring were tested and found to be functioning properly. Inspected Components Blower wheel and primary drain pan are in good condition and operating correctly. All electrical wires were secured. Temperature Readings Return air temperature measured at 72.0 degrees Fahrenheit. Supply air temperature measured at 52.0 degrees Fahrenheit. Condensate Drain System Cleared the drain line, cleaned the primary pan, and tested the safety switch. Addit

Today, I arrived on site to perform winter maintenance on the HVAC equipment. Overall Equipment Condition: * Good condition noted for both indoor and outdoor units. Indoor Unit Details: * Located in the closet as an air handler. * Services the whole home. * Pleated filter (2-6") replaced today, size 20x25. * Indoor coil is clean and in good condition, brush cleaned today. Outdoor Unit Details: * Located on the side of the house as a heat pump. * Outdoor coil is clean and in good condition, cleaned today. Electrical Components: * All tested components are functioning properly within manufacturer specifications: * Blower Motor * Inducer Draft Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Blower Run Capacitor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Electrical Wiring * No components were found to be malfunctioning. System Inspection: * Blower Wheel, Primary Drain Pan, Secondary Drain Pan, and Electrical Wires are in good conditio

Performed a winter time tune up on the hvac equipment. Testing system operations, component amperage’s, capacitor ratings, cleared the drain line, changed the filters, dusted the return grills, tested the thermostat, and washed the condenser coil outside. The system is working properly at this time in heating and cooling modes.

Found the load shed generator to be faulty again, I placed a service call with Mathers electric for the customer. The neighbor bypassed the load shed box for her so she wouldn’t be without air again. The system is working properly, just has a faulty load shed box that Mathers will repair.

HVAC Repairs: Called out for an HVAC system that was excessively vibrating. Upon arrival, I identified damaged compressor isolation mounts in the client's HVAC system. I replaced the mounts to reduce vibration and ensure stable operation of the compressor.

I performed a summertime tune up on the hvac equipment. Tested system operations, component amperage’s, capacitor ratings, cleared the drain line, replaced the air filters, tested the thermostat, and cleaned the condenser outside. The system is working properly at this time.

Diagnostic system not heating. I found there was no high voltage going to the air handler so the system would not come on. The generator load shed module is faulty and was interrupting the high voltage going to the air handler. I unwired and bypassed the generator load shed module to get the system up and running. Need to call Mathers Electric 576-2342 to replace the contactor in the generator load shed module. The system is now up and running and heating properly at this time.

Performed a winter time tune up on your hvac equipment. The system is working properly in heating mode. View checklist from todays maintenance here… https://visionshare.xoi.io/?id=XA-FBE9-B6EED32E16E94EF28E6F4CDA1A864ECC