Quincy, FL HVAC Service

07/13/2026- I arrived on site to find the unit satisfied at 76 degrees. I preformed a full daignosic and found no issues at this time. The unit is functioning properly, all electrical equipment is within specifications, and the unit is cooling properly with a 19 degree temperature split. I informed the customer that what is most likely occurring is this is an old house and hot air is likely leaking into the house. This is making the unit hit its maximum cooling capacity during this hot weather, and why this unit has no issues whatsoever when it’s not extremely hot outside. I informed the customer that the unit is currently cooling properly and to contact us if she has any issues.

Today I arrived on site to perform a summer tune-up on your GOODMAN package unit. System Overview Inspected the overall equipment condition, noted as fair. Located the indoor and outdoor package units in the whole home area and backyard, respectively. Filtration & Coils Checked the Respicare, pleated 1" filters (two 10x16x1). Customer declined new filters, stating they will provide their own. Inspected both indoor and outdoor coils; both are in fair condition. Electrical Component Checks Tested and confirmed the following electrical components are working properly within manufacturer specifications: Blower Motor Compressor Blower Run Capacitor Compressor Run Capacitor Fan Run Capacitor Contactor Electrical Wiring System Component Inspections Inspected and found the following components in good condition and working properly: Blower Wheel Primary Drain Pan Electrical Wires Secured Ductwork Cleared the condensate drain line and confirmed it is connected and strapped down. Operational

Today I arrived on site to perform a summer tune-up on your system. Indoor Unit Service Located the Air Handler in the attic closet. Confirmed the unit services the whole home. Replaced and washed the washable, pleated 1" filter. Noted the customer declined additional filters and will provide their own. Checked the 20x20x1 and 20x20x4.5 filters. Inspected the indoor coil; condition is fair. Dusted the return grills and thermostat. Checked and tested the thermostat batteries and operation. Checked the UV light; it is on and shining, but the bulb needs replacement. Outdoor Unit Service Located the Heat Pump in the backyard. Inspected the outdoor coil; condition is fair. Electrical Component Checks Tested the Blower Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, and Electrical Wiring; all are working within manufacturer specifications. System Component Inspections Inspected the Blower Wheel, Primary Drain Pan, Electrical Wires Secured,

Today I arrived on site to perform a summer tune-up on your GOODMAN package unit. Overall System Condition The GOODMAN package unit is in fair condition. The indoor and outdoor coils are in fair condition. Electrical Component Checks Tested and confirmed proper operation of the blower motor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor, electrical wiring, and contactor. Component Inspections Inspected the blower wheel, primary drain pan, electrical wires, and ductwork; all are in good condition. Airflow and Drainage Measured return air temperature at 75.0°F and supply air temperature at 55.0°F. Cleared the condensate drain line and tested the safety switch. Confirmed the drain line is connected and strapped. Additional Checks Checked the operation of the UV light; it is on and shining. The customer declined filters and will provide their own 16x20x1 filter. Your system is working properly at this time. View visual findings from this job here - htt

Today I arrived on site and performed a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Located the air handler in the garage, servicing the downstairs area. * Checked the pleated 1" filter, size 14x20x1. * Inspected the primary drain pan, electrical wires, ductwork, and blower wheel; all are in good condition. * Cleared the condensate drain line and tested the safety switch. * Confirmed the drain line is strapped and secured. * Recorded return air temperature at 78.0°F and supply air temperature at 45.0°F. **Outdoor Unit Service** * Located the heat pump on the side of the building. * Noted the outdoor coil is in fair condition. **Electrical System Check** * Tested the condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working within manufacturer specifications. **Overall Status** * The overall equipment condition is good.

Today I arrived on site and performed a summer maintenance on your HVAC equipment. **Overall System Status** * Overall equipment condition: Fair. * Indoor unit: Air Handler in the closet. * Outdoor unit: Heat Pump on the side of the house. * Serviced: Whole home. **Maintenance Actions** * Cleaned the outdoor coil. * Cleared the condensate drain line. * Tested the condensate drain safety switch. * Ensured the drain line is strapped. * Restored power to the units. * Tested operations of the thermostat. **Component Inspections & Tests** * **Electrical Components (Working Properly):** Condenser Fan Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Compressor Start Capacitor, Contactor, Electrical Wiring. * **System Components (Good Condition):** Primary Drain Pan, Electrical Wires Secured. * **Filtration:** Pleated 1" filter, size 18x18x1. * **Coil Conditions:** Indoor coil good, outdoor coil cleaned. **Performance Reading

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service** * Checked the pleated 1" filter (12x20). * Cleared the condensate drain line and tested the safety switch. * Inspected the blower wheel and secured electrical wires. **Outdoor Unit Service** * Cleaned the dirty outdoor coil. **Electrical Component Checks** * Tested the condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working within manufacturer specifications. **System Operations** * Restored power to the units. * Tested thermostat operations. * Measured return air temperature at 75.0°F and supply air temperature at 64.0°F. The overall equipment condition is fair.

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Overall Equipment Condition** * Found overall equipment condition fair. * The indoor package unit is located in the attic. * The outdoor unit is on the side of the house. **Filtration and Coils** * Checked the 1" pleated filter. * Found the indoor coil in fair condition. * Found the outdoor coil in fair condition. **Electrical Components** * Tested and inspected the blower motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring; all are working within manufacturer specifications. **System Components** * Inspected the blower wheel, primary drain pan, secondary drain pan, and ductwork; all are in good condition. * Ensured electrical wires are secured. **Temperature Readings** * Measured return air temperature at 87.0 degrees Fahrenheit. * Measured supply air temperature at 59.0 degrees Fahrenheit. **Condensate Drain System** * Cleared th

Today I performed maintenance on your American Standard heat pump unit. The system is cooling properly at this time. Thank you for your business. Quincy FL

On arrival I found a customer system not cooling properly due to the condenser fan motor over ramping I’m going off on thermal overload. The customer had the system off when I arrived so everything came on and started cooling properly, but then I noticed a condenser motor to be over ming it was rated for .5A and it was bouncing back-and-forth between .6A and .7A I sent the customer an estimate to change the condenser fan motor and contactor. The contactor is functioning properly, but I recommend changing it with the condenser fan motor due to the wear and tear put on it over the years. The system is on and cooling at this time. I highly recommend getting the motor replaced as soon as possible .

Today I arrived on site to perform a summer tune-up on your CARRIER system. System Overview Indoor Unit: Located in the attic, a garage air handler, servicing the whole home. Overall condition: Fair. Indoor coil condition: Fair. Outdoor Unit: A heat pump located on the side of the house. Overall condition: Fair. Outdoor coil condition: Fair. Maintenance Performed Filtration: Noted pleated 1" filter, size 20x20x1. Customer declined filters, will provide their own. Electrical Components:Tested and inspected the blower motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. All are working properly within manufacturer specifications. Component Inspection:Inspected the blower wheel, primary drain pan, electrical wires secured, ductwork, and secondary drain pan. All are in good condition and working properly. Condensate Drain System:Cleared the drain line and tested the safety switch. Confirmed the drain line is connected and

Today I arrived on site to perform summer maintenance on your HVAC equipment. ### Indoor Unit Service * Checked and replaced the 1" pleated 20x20x1 filter for the UPSTAIRS and CRAWL SPACE AIR HANDLERS using customer-provided spares. * Inspected the indoor coil, finding it in good, clean condition. * Confirmed the blower wheel and ductwork are in good condition. ### Outdoor Unit Service * Cleaned the outdoor coil on the heat pump, noting its fair condition. ### Electrical Component Checks * Tested the blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, defrost control board, and electrical wiring; all are working within manufacturer specifications. * Inspected electrical wires, confirming they are secured. ### System Operations & Drainage * Cleared the condensate drain line, cleaned the primary and secondary drain pans, and tested the safety switch. The drain line is strapped and secured. * Test

Performed a summer time tune up on the hvac equipment. Testing system operations, component amperage’s, capacitor ratings, cleared the drain lines, tested the thermostats, replaced the air filters, and dusted the return grills. The systems are working properly at this time in cool mode. I used last 16x20 air filter today and will can bring another case at the next visit for $120.00.

Today I arrived on site to perform a summer maintenance on your HVAC equipment. **Indoor Unit Service (Air Handler - Attic)** * Checked the Respicare filter, size 20x20x1. * Inspected the indoor coil; condition is fair. * Tested the safety switch on the condensate drain system. * Confirmed the condensate drain line is connected and strapped. * Measured return air temperature at 86.0°F and supply air temperature at 64.0°F. **Outdoor Unit Service (Heat Pump - Backyard)** * Inspected the outdoor coil; condition is fair. **Electrical Component Checks** * Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring. **System Component Inspections** * Inspected the blower wheel, secondary drain pan, primary drain pan, secured electrical wires, and ductwork; all are in good condition. **Operational Checks** * Rest

Today I arrived on site to perform a summer tune-up on your system. **Indoor Unit Service** * Checked the overall condition of the indoor unit in the closet; it is fair. * Washed the washable, pleated 2-6" whole home filter (size 20x25x5). * Inspected the indoor coil; it is in fair condition. **Outdoor Unit Service** * Checked the overall condition of the outdoor unit in the backyard; it is fair. * Inspected the outdoor coil; it is in fair condition. **Electrical Component Checks** * Tested and confirmed proper operation of the Blower Motor, Condenser Fan Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Compressor Start Capacitor, Contactor, and Electrical Wiring. **System Component Inspections** * Inspected the Blower Wheel, Secondary Drain Pan, Primary Drain Pan, and Electrical Wires Secured; all are in good condition. **Drainage System Maintenance** * Cleared the drain line. * Cleaned out the primary and secondary drain pan

Today I arrived on site to perform a summer tune-up on your TRANE package unit. Indoor Unit Service Inspected the indoor package unit, noting its fair condition. Checked the pleated 1" filters (2) 16x20x1; customer will provide replacements. Inspected the indoor coil, noting its fair condition. Tested return air temperature at 75.0°F and supply air temperature at 57.0°F. Outdoor Unit Service Inspected the outdoor package unit in the backyard, noting its fair condition. Checked the outdoor coil, noting its fair condition. Electrical Component Checks Tested the blower motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring. All are working properly within manufacturer specifications. System Component Inspections Inspected the blower wheel, primary drain pan, secured electrical wires, and ductwork; all are in good condition. Cleared the condensate drain line and tested the safety switch. Confirm

Today I arrived on site to perform a summer tune-up on your GOODMAN system. Indoor Unit Service Inspected the Air Handler in the attic; its overall condition is fair. Washed the washable, pleated 2-6" filter (20x20) today. Checked the indoor coil; its condition is fair. Cleared the condensate drain line and tested the safety switch. Confirmed the drain line is strapped and secured. Verified the UV light is on and shining. Outdoor Unit Service Inspected the Heat Pump in the backyard; its overall condition is fair. Checked the outdoor coil; its condition is fair. Electrical Component Checks Tested and confirmed proper operation of the Blower Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, and Electrical Wiring. System Component Inspections Inspected the Blower Wheel, Secondary Drain Pan, Primary Drain Pan, Ductwork, and Electrical Wires; all are in good condition. System Performance & Adjustments Recorded a return air temperature of 70.0

Today I arrived on site to perform a summer tune-up on your GOODMAN system. Indoor Unit Service Inspected the Air Handler in the closet; condition is fair. Washed the 20x25 pleated 2-6" washable filter. Checked the indoor coil; condition is fair. Tested the blower motor, blower run capacitor, and electrical wiring; all are working properly. Inspected the blower wheel, primary drain pan, electrical wires, and ductwork; all are in good condition. Measured return air temperature at 75.0°F and supply air temperature at 54.0°F. Outdoor Unit Service Inspected the Heat Pump on the side of the house; condition is fair. Checked the outdoor coil; condition is fair. Tested the compressor, compressor run capacitor, fan run capacitor, and contactor; all are working properly. Drainage and Other Checks Cleared the condensate drain line and tested the safety switch. Confirmed the drain line is strapped and secured. Checked the UV light; it is on and shining. Dusted the return grills and thermostat.

Today I arrived on site to perform a winter tune-up on your JANITROL system. System Overview The indoor air handler is located in the closet, and the outdoor heat pump is in the backyard. The system services the whole home. Overall equipment condition is fair. Maintenance Performed Filtration: Checked the 18x18x1 pleated 1" filter. Coils: Inspected both the indoor and outdoor coils; both are in fair condition. Electrical Components:Tested the blower motor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. All are working properly within manufacturer specifications. System Components:Inspected the blower wheel, primary drain pan, secured electrical wires, and ductwork; all are in good condition. Drainage:Tested the condensate drain system safety switch and cleared the drain line. Confirmed the drain line is connected and strapped down. Temperatures:Measured return air temperature at 69.0°F. Measured supply air temperature at 82.0°F. A

Today I arrived on site to perform a summer tune-up on your GOODMAN system. System Overview Overall Equipment Condition: Fair. Indoor Unit: Air Handler located in the closet. Outdoor Unit: Heat Pump located in the back yard. Service Area: Whole home. Maintenance Performed Filtration: Checked the 20x20x1 pleated 1" filter. Customer declined new filters and will provide their own. Indoor Coil: Noted as dirty; recommend a duct cleaning. Outdoor Coil: Condition is fair. Condensate Drain System: Cleared the drain line and tested the safety switch. Electrical Components:Tested and Working Properly: Blower Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, Electrical Wiring. Inspected and in Good Condition: Blower Wheel, Primary Drain Pan, Electrical Wires Secured, Ductwork. Temperatures:Return Air Temperature: 77.0°F. Supply Air Temperature: 55.0°F. Other Actions: Dusted the return grills and thermostat, restored power to units, checked thermost

Today I arrived on site to perform a summer tune-up on your CARRIER system. System Overview Overall Equipment Condition: Fair. Indoor Unit: Closet, Air Handler. Outdoor Unit: Side of House, Heat Pump. Area Serviced: Whole Home. Maintenance Actions Filtration: Checked the 18x24x1 pleated 1" filter. Customer declined new filters and will provide their own. Coil Condition: Inspected both indoor and outdoor coils; both are in fair condition. Electrical Components:Tested and confirmed proper operation of the Blower Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, and Electrical Wiring. System Components:Inspected Blower Wheel, Primary Drain Pan, Electrical Wires Secured, and Ductwork; all are in good condition. Condensate Drain System: Cleared the drain line and tested the safety switch. Confirmed the drain line is strapped. General: Dusted return grills and thermostat. Restored power and tested thermostat operations. Operational Status Retur

Performed tune up on your Goodman furnace and AC system. Cleared drain line, checked all electrical components, and rinsed condenser. Checked out the loud noise coming from air handler. It appears to be the bearings failing on the blower motor. This was causing a loud noise to come from the furnace when the blower was running. Estimate is attached to replace both the blower motor and blower wheel. The furnace is not under warranty as it was not replaced with the coil and condenser. Thank you for your business. View visual findings from this job here - https://visionshare.xoi.io/?id=XA-05B7-B957E5B90E0D4AE996172CECAA454DFB

Today I arrived on site and performed a summer maintenance on your HVAC equipment. Indoor Unit Service Located the air handler in the attic. Checked and replaced the pleated 1" filters (sizes 20x30x1 and 12x12x1). Customer provided their own filters. Inspected the indoor coil; condition is fair. Checked the blower wheel and primary drain pan; both are in good condition. Inspected ductwork and ensured electrical wires are secured. Outdoor Unit Service Located the heat pump on the side of the house. Inspected the outdoor coil; condition is fair. Electrical Component Checks Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. System Performance & Maintenance Measured return air temperature at 70.0°F and supply air temperature at 48.0°F. Cleaned out the primary drain pan, cleared the drain line, and tested the safety switch. Dusted the thermostat, checked its batteries,

Today I arrived on site to perform maintenance on your units. **Maintenance Performed:** * Checked return air temperature: 73 degrees. * Checked supply air temperature: 50 degrees. * Washed washable filters. * Tested mini split remote. * Restored power to unit. **Additional Actions:** * Dusted mini split remote. * Wore shoe covers **Recommendations:** * Mini split indoor unit cleaning **Summary** * Unit is working properly today Tallahassee Fl View visual findings from this job here - https://visionshare.xoi.io/?id=XA-C335-22CEC17B0EC745AEAB79567EDE3AB31A

Today I arrived on site to perform maintenance on your whole home air handler and heat pump system. Indoor Unit (Air Handler) Service: Located the air handler in the attic. Replaced the Respicare filter with a new 16x20x1 filter. Inspected the indoor coil; it is clean and in fair condition. Outdoor Unit (Heat Pump) Service: Located the heat pump in the backyard. Inspected the outdoor coil; it is clean and in fair condition. Electrical Component Checks: Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, and all associated run and start capacitors. Verified the contactor and electrical wiring are working within manufacturer specifications. System Component Inspections: Inspected the blower wheel, primary and secondary drain pans, and ductwork; all are in good condition. Confirmed electrical wires are secured. Operational Status: Measured return air temperature at 76.0°F. Measured supply air temperature at 53.6°F. Overall equipment condition i