Quincy, FL HVAC Service

Today I arrived on site to perform a complete tune-up on your package unit system, serving the whole home. The system is currently in good condition and working properly. **Maintenance and Cleaning Activities** * Cleaned the outdoor coil located in the back yard. * Checked the 20x20x1 pleated filter; left replacement to you per your preference. * Cleared the condensate drain line, ensured it is properly strapped, and cleaned out the primary drain pan. * Dusted the return grills and thermostat. **Inspections and Testing** * Inspected and confirmed the indoor coil, blower wheel, burners, exhaust flue, heat exchanger, and primary drain pan are in good condition. * Tested the blower motor, compressor, electrical wiring, contactor, and all run capacitors (blower, compressor, and fan); all are working properly within manufacturer specs. * Tested carbon monoxide levels, reading at a safe 0.00 PPM. * Recorded a return air temperature of 75.0°F and a supply air temperature of 102.0°F. **The

Cleaned mini split blower wheel and coil and filters, everything looks good and is working properly at this time.

Today I arrived on site and performed a tune-up on your whole-home package unit HVAC system, which is in fair condition and working properly. **System Inspection & Maintenance** * **Indoor & Outdoor Coils:** Inspected the indoor coil and outdoor coil; both are clean and in fair condition. * **Filtration:** Verified 20x20x1 pleated filter size; filter replacement left to customer per request. * **Condensate Drain System:** Cleared the drain line, cleaned out the primary pan, and confirmed the drain line is properly secured with hanging straps. * **Components & Safety:** Inspected the blower wheel, burners, exhaust flue, primary drain pan, ductwork, and secured electrical wiring; all are in good condition. Tested carbon monoxide levels at 0.00 PPM. **Electrical & Operational Testing** * **Electrical Components:** Tested and confirmed proper operation within manufacturer specifications for the blower motor, inducer draft motor, condenser fan motor, compressor, compressor run capacitor,

Today I performed a deep cleaning on your Mitsubishi mini split units and tested system operations afterwards. Everything is working properly at this time. Thank you for your business. Quincy FL

Today I arrived on site and performed a complete HVAC system tune-up on your package unit. Below is a summary of the service activities completed: **System Maintenance & Cleaning** * Inspected the package unit, noting the overall equipment, indoor coil, and outdoor coil in fair condition. * Cleaned the outdoor coil. * Inspected the 18x18x1 pleated 1" filter. * Cleared the condensate drain line, verified proper connections, and ensured it was securely strapped. **Component Inspection & Electrical Testing** * Tested and confirmed proper operation within manufacturer specifications for the blower motor, heat strip kit, condenser fan motor, compressor, contactor, electrical wiring, and all capacitors (blower run, compressor run, fan run, compressor start). * Inspected the blower wheel, primary drain pan, and electrical wiring connections, confirming all are secured and in good condition. **System Testing & Operational Status** * Restored power to the unit and tested thermostat operation

Today I arrived on site and performed a tune-up on the HVAC system, ensuring all equipment is operating properly. **Indoor Unit (Air Handler - Garage)** * Inspected the Air Handler unit and indoor coil, finding both in fair condition. * Replaced the 20x30x1 pleated air filter using customer-provided spare filters. * Inspected and verified the blower wheel, primary drain pan, and secured electrical wiring are in good condition. * Cleared the condensate drain line, verified it is properly strapped, and successfully tested the drain safety switch. **Outdoor Unit (Heat Pump - Back Yard)** * Inspected the Heat Pump outdoor unit and outdoor coil, finding both in fair condition. **Electrical & Operational Testing** * Tested the blower motor, heat strip kit, condenser fan motor, compressor, contactor, and electrical wiring. * Tested all run and start capacitors (blower, compressor, and fan). * Confirmed all electrical components are operating properly within manufacturer specifications. *

Today I arrived on site to perform a routine maintenance tune-up on the HVAC system, servicing the west side of the property. The equipment is currently in good condition and working properly. **Indoor Unit (CLOSET AHU 1)** * Washed the 20x20x5 washable air filter. * Inspected the indoor coil, blower wheel, secondary drain pan, and secured electrical wiring, confirming all are in good condition. * Cleared the condensate drain line, verified it is properly secured with hanging straps, and tested the safety switch. **Outdoor Unit (CONDENSER 1)** * Inspected the heat pump outdoor unit and coil in the back yard, confirming good condition. **System Testing & Performance** * Tested and verified proper operation within manufacturer specifications for the blower motor, heat strip kit, condenser fan motor, compressor, contactor, defrost control board, electrical wiring, and all capacitors (blower run, compressor run, fan run, compressor start). * Recorded a return air temperature of 67.0°F

Today I arrived on site and performed a comprehensive inspection and maintenance on the whole-home Heat Pump and closet Air Handler system. **Equipment Condition & Maintenance** * Checked the Air Handler indoor coil, Heat Pump outdoor coil, and overall system condition, finding all in fair shape. * Replaced the 16x20x1 pleated air filter using the customer's spare filters. * Serviced the condensate drain system by clearing the drain line, cleaning the primary and secondary drain pans, and testing the safety switch. **System Testing & Inspection** * Inspected the blower wheel, primary and secondary drain pans, secured electrical wiring, and ductwork; all are in good condition and operating properly. * Tested electrical components—including the blower motor, heat strip kit, condenser fan motor, compressor, run capacitors, contactor, defrost control board, and wiring—and confirmed all are operating within manufacturer specifications. * Measured system temperatures, recording a return a

Today I arrived on site and performed a tune-up on the whole-home HVAC system, including the CLOSET AHU, ATTIC AHU, CON 1, CON 2, and CON 3 units. The equipment is currently in fair condition and working properly. **System Maintenance & Inspection** * Replaced the Respicare air filters for the CLOSET AHU and ATTIC AHU using customer-provided spares (sizes 16x20x1 and 20x20x1). * Inspected the indoor coil, outdoor heat pump coil, blower wheel, ductwork, primary drain pan, and secondary drain pan. * Confirmed the condensate drain line is properly secured and strapped. * Dusted the return grills and thermostat. **Drain System Service** * Cleared the condensate drain line. * Cleaned out both the primary and secondary drain pans. * Tested the safety switch to ensure proper operation. **Electrical & Operational Testing** * Tested electrical components and confirmed they are operating within manufacturer specifications: Blower Motor, Heat Strip Kit, Condenser Fan Motor, Compressor, Blower

Performed maintenance on both systems. Tested electrical components, cleared drain lines, cleaned condenser coils, replaced a capacitor, and repaired insulation on outdoor refrigerant lines. Both systems are heating properly at this time.

Today I arrived on site and performed a complete HVAC system tune-up on your Attic Furnace and Back Yard Straight Cool units. The equipment is in good condition and operating properly. ### Service Activities * **Air Filtration:** Checked and washed the 20x25x4 washable filter. * **Coil & Component Inspection:** Inspected the indoor coil, outdoor coil, blower wheel, heat exchanger, burners, exhaust flue, ductwork, and primary and secondary drain pans; all are clean and in good condition. * **Electrical System Testing:** Tested the blower motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, and secured electrical wiring. All components are functioning properly within manufacturer specifications. * **Condensate Drain Maintenance:** Cleared the drain line (verified properly strapped), cleaned the primary and secondary pans, cleaned the condensate pump, and tested the safety switch. * **System Performance & Safety:** Tested carbo

Today I arrived on site to perform a system tune-up on the Mini Split and Package Unit servicing the upstairs and downstairs areas. **System Inspection & Maintenance** * Checked the general condition of the indoor units, outdoor condenser, indoor coils, and outdoor coils; all were clean and in good condition. * Checked the 18x24x1 and 12x20x1 1" pleated filters; customer declined replacement to provide their own. * Inspected the blower wheel, ductwork, primary drain pan, and secured electrical wiring, confirming all are in good condition. * Cleared the condensate drain line, cleaned the primary drain pan, and verified the drain line is properly strapped and secured. **Electrical Testing & Repairs** * Tested electrical components: blower motor, condenser fan motor, compressor, blower run capacitor, contactor, defrost control board, and wiring were operating within manufacturer specs. * Identified failing components and replaced the compressor run capacitor and condenser fan motor run

Today I arrived on site and performed a tune-up on the HVAC system. The equipment is in fair overall condition and is working properly at this time. **Filter Maintenance** * Replaced the 20x25x4 pleated filters for the DOWNSTAIRS AHU and UPSTAIRS AHU using the customer's spare filters. **Component Inspections & Electrical Testing** * Inspected the indoor coils, outdoor coils, blower wheels, primary and secondary drain pans, secured electrical wiring, and ductwork; all are in good, working condition. * Tested the following electrical components on the DOWNSTAIRS CON and UPSTAIRS CON, confirming they operate within manufacturer specifications and amperages: * Blower Motor and Condenser Fan Motor * Compressor * Blower, Compressor, and Fan Run Capacitors * Contactor and Defrost Control Board * Electrical Wiring **Condensate System Maintenance** * Cleared the condensate drain line, ensuring it is properly secured with hanging straps. * Cleaned out the primary and secondary dra

Today I arrived on site and performed a tune-up on your HVAC system. Indoor Unit Service Located the AIR HANDLER in the attic. Washed the washable filter and replaced the pleated 1" filters with customer-provided spares (sizes 20x25x1 & 12x12x1). Inspected the indoor coil; it is fair and clean. Inspected the blower wheel, primary drain pan, secondary drain pan, and electrical wires; all are in good condition and secured. Outdoor Unit Service Located the Heat Pump on the side of the house. Inspected the outdoor coil; it is good and clean. Electrical System Check Tested the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly within manufacturer specifications. Checked the UV light; it is on and shining. Drainage System Maintenance Cleared the condensate drain line. Cleaned out the primary drain pan. Tested the safety switch. Ensured the drain line is connecte

Today I arrived on site to perform a tune-up on your HVAC system. Indoor Unit Service Inspected the air handler in the closet; overall condition is fair. Checked the 24x24x1 pleated 1" filter. Inspected the indoor coil; condition is fair. Tested return air temperature at 75.0°F and supply air temperature at 59.0°F. Outdoor Unit Service Inspected the heat pump on the side of the house; overall condition is fair. Checked the outdoor coil; condition is fair. Electrical Component Checks Tested blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring; all are working properly within manufacturer specifications. System Component Inspections Inspected the blower wheel, primary drain pan, secured electrical wires, and ductwork; all are in good condition. Condensate System Maintenance Cleared the drain line. Cleaned out the primary pan. Tested the safety switch. Confirmed the drain line is connected and strapped down. Addition

Today I arrived on site to perform a tune-up on your HVAC system. Indoor Unit Service Inspected the Air Handler in the crawl space; overall condition is fair. Washed the 20x20 pleated 2-6" washable filter. Noted the indoor coil is in fair condition. Checked the blower wheel, primary drain pan, electrical wires, and ductwork; all are in good condition. Outdoor Unit Service Inspected the Heat Pump on the side of the house; overall condition is fair. Noted the outdoor coil is in fair condition. Electrical Component Checks Tested the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring; all are working properly within manufacturer specifications. System Performance & Maintenance Measured return air temperature at 73.0°F and supply air temperature at 55.0°F. Cleared the condensate drain line, cleaned the primary pan, cleaned the condensate pump, and tested the safety switch. Confirmed the condensate drain line is conne

Today I arrived on site to perform a tune-up on your HVAC system. System Overview Overall equipment condition: Fair. Indoor unit: Package Unit. Outdoor unit: Package Unit, located in the backyard. Area serviced: Whole Home. Filtration Filtration type: Pleated 1". Filter size: (2) 20x25. Customer will provide new filters for replacement. Component Inspection & Service Coils:Indoor coil condition: Fair. Outdoor coil condition: Fair. Electrical Components (Tested & Working Properly):Blower Motor Condenser Fan Motor Compressor Compressor Run Capacitor Fan Run Capacitor Contactor Electrical Wiring Components Inspected (Good Condition & Working Properly):Blower Wheel Primary Drain Pan Electrical Wires Secured Ductwork Condensate Drain System:Cleared drain line. Cleaned out primary pan. Ensured drain line is connected and strapped. Operational Checks Return Air Temperature: 70.0°F. Supply Air Temperature: 54.0°F. Restored power to the units. Checked and replaced batteries in the thermostat.

Today I arrived on site to perform a tune-up on your HVAC system. **Indoor Unit Service** * Located the air handler in the crawl space. * Washed and checked the 20x25x4 washable filter. * Inspected the indoor coil; it is clean and in good condition. * Cleared the condensate drain line and cleaned out the primary pan. * Tested the safety switch and ensured the drain line is strapped. * Inspected the blower wheel, heat exchanger, primary drain pan, and ductwork; all are in good condition. * Confirmed electrical wires are secured. **Outdoor Unit Service** * Located the heat pump on the side of the house. * Cleaned and inspected the outdoor coil; it is in good condition. **Electrical Component Checks** * Tested and inspected the blower motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, defrost control board, and electrical wiring. All are working properly within manufacturer specifications. **System Operations & Final Ch

Today I arrived on site to perform a tune-up on your HVAC system. UNIT #2 CONDENSER Service * Inspected the outdoor coil; it is clean and in good condition. * Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring; all are working properly within manufacturer specifications. UNIT #2 AIR HANDLER Service * Replaced the 16x20x4 pleated 2-6" filter. * Inspected the indoor coil; it is clean and in good condition. * Tested the blower motor and electrical wiring; both are working properly within manufacturer specifications. * Inspected the blower wheel and primary drain pan; both are in good condition. * Cleared the condensate drain line, cleaned the primary pan, and tested the safety switch. * Confirmed the drain line is connected and strapped. * Checked the UV light; it is on and shining. * Measured return air temperature at 75.2°F and supply air temperature at 54.6°F. General Maintenance * Dusted the return grills and ther

Today I arrived on site to perform a summer maintenance on your HVAC equipment. ### Indoor Unit Service * Inspected the package unit, noting its fair condition. * Observed the indoor coil is in fair condition; recommend a duct cleaning. * Confirmed whole home services were completed. * Noted customer will provide their own pleated 1" filters. * Checked the blower wheel, primary and secondary drain pans, electrical wires, ductwork, and burners; all are in good condition. * Tested the blower motor, blower run capacitor, contactor, electrical wiring, and furnace control board; all are working within manufacturer specifications. ### Outdoor Unit Service * Inspected the outdoor unit located on the side of the house, noting its fair condition. * Checked the outdoor coil, finding it in fair condition. * Tested the condenser fan motor, compressor, compressor run capacitor, and fan run capacitor; all are working within manufacturer specifications. ### System Diagnostics & M

Today I arrived on site to perform a summer maintenance on your HVAC equipment. Indoor Unit Service (AIRHANDLER) Located the AIRHANDLER in the closet. Washed the 20x25x5 washable filter. Confirmed the indoor coil is clean and in good condition. Cleared the condensate drain line, tested the safety switch, and cleaned out the primary drain pan. Inspected the blower wheel, secondary drain pan, primary drain pan, secured electrical wires, and ductwork; all are in good condition. Tested the blower motor and blower run capacitor; both are working properly. Return air temperature was 74.0°F, and supply air temperature was 55.0°F. Outdoor Unit Service (CONDENSER) Located the CONDENSER (heat pump) on the side of the house. Confirmed the outdoor coil is clean and in good condition. Tested the condenser fan motor, compressor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly. System Checks Dusted the thermostat,

Today I arrived on site to perform a summer maintenance on your HVAC equipment. Indoor Unit Service (Air Handler) Located the Air Handler in the garage attic. Replaced the pleated 1" filters with sizes 18x24x1, 16x25x1, and 12x12x1. Confirmed the indoor coil is clean and in good condition. Cleared the condensate drain line, cleaned the primary drain pan, and tested the safety switch. Inspected the condensate drain line, ensuring it is connected and strapped down. Verified the blower wheel, secondary drain pan, primary drain pan, secured electrical wires, and ductwork are in good condition. Outdoor Unit Service (Heat Pump) Located the Heat Pump in the backyard. Cleaned the outdoor coil, which is in good condition. Electrical Component Checks Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring. System Performance & Genera

Today I arrived on site to perform a summer maintenance on your HVAC equipment. Indoor Unit Service Inspected the FURNACE in the closet. Replaced the 20x20x1 pleated 1" filter. Confirmed the indoor coil is clean and in good condition. Tested for carbon monoxide, reading 0.00 PPM. Noted return air temperature at 69.0°F and supply air temperature at 50.0°F. Outdoor Unit Service Inspected the Straight Cool CONDENSER on the side of the house. Confirmed the outdoor coil is clean and in good condition. Electrical Component Checks Tested and confirmed proper operation of the Blower Motor, Condenser Fan Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Compressor Start Capacitor, Contactor, Electrical Wiring, and Furnace Control Board. System Component Inspections Inspected and confirmed good condition and proper operation of the Blower Wheel, Burners, Exhaust Flue, Heat Exchanger, Primary Drain Pan, Electrical Wires Secured, and Ductwork. Condensate System

Today I arrived on site to perform summer maintenance on your HVAC equipment. Air Handler Service (East Side, Closet) Replaced the 20x20x1 pleated 1" filter. Confirmed the indoor coil is clean and in fair condition. Cleared the condensate drain line, tested the safety switch, and cleaned the primary drain pan. Ensured the condensate drain line is connected and strapped. Checked the blower wheel, primary drain pan, and ductwork; all are in good condition. Heat Pump Service (Back Yard) Confirmed the outdoor coil is clean and in fair condition. Electrical System Check Tested the blower motor, condenser fan motor, compressor, and all associated run and start capacitors. Inspected the contactor and electrical wiring. All components are working properly within manufacturer specifications. Confirmed electrical wires are secured. System Operations & General Maintenance Measured return air temperature at 80.0°F and supply air temperature at 57.0°F. Dusted the thermostat, checked its batteri

08/04/2026- I arrived on site and replaced the faulty air handler control board with OEM equipment. After the installation of the new control board I tested the unit and have verified that the system is now functioning correctly and without any issues. The new control board has been set up with the same dip switch configuration as the previous control board and I have found no issues of the new boards operation. The unit itself is functioning and cooling properly at the time of service.