Crawfordville, FL HVAC Company

Found the system to be low on charge. I added 3 pounds of R-410A refrigerant to get the system working properly. I performed an electronic leak search on the evaporator coil and copper lines but was unable to pin point a leak at the time. The system is now working properly at this time.

Today I performed a winter time maintenance on your HVAC equipment. Overall everything looked to be in fair to poor condition. I started off checking the difference in temperature between supply and return air. I observed a return air temp of 70° while supply air was 59°F. This is a low temperature split for the efficiency rating of your unit, which tells me there’s something going wrong. The indoor conditioning (evaporator) coil was relatively clean considering the age, but in poor condition. I checked the operation of the compressor, condenser fan and their respective capacitor. Everything was within manufacturer specifications. Pressures looked low, I couldn’t read subcool and superheat due to there being no access to the compressor aside from the top where the fan is. I finished up treating the drain with chemical to prevent a clog. I have scheduled a service and new unit quote appointment for you on Monday 2/23/25. Thank you for choosing

Today I performed a winter time tune up on your HVAC equipment. I started off checking the difference in temperature between supply and return air. I observed a return of 72° while supply air was 55°F. The filter is good to go for another couple months. Outside I checked the operation of the compressor, condenser fan and their respective capacitor. Everything was within manufacturer specifications. The condenser coil was hosed out today. I finished up treating the drain with chemical to prevent a clog. Thank you for choosing

Today I performed a winter time maintenance on your HVAC equipment. Overall everything looked to be in good condition. I started off checking the difference in temperature between supply and return air. I observed a return of 72° while supply was 53°F. Right where we want it. Outside I checked the operation of the compressor, condenser fan and their respective capacitor. Everything was within manufacturer specifications. The condenser coil was washed out with water only. I finished up clearing the drain using the wet vac. Once I was sure the drain was clear I treated the assembly with Viper drain treatment. Thank you for choosing

Performed a summertime tune up on the equipment. Testing system operations, component amperage’s, capacitor ratings, cleared the drain line, checked the filter, tested the thermostat, dusted the return grill, and cleaned the evaporator coil. The system is working properly at this time conditioning the supply air down to 48 degrees.

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Garage/Attic):** * Observed the indoor unit to be in fair condition. * Verified the indoor coil is clean and in fair condition. * Noted the filter size is 20x25x1, pleated 1". * Customer has spare filters and will replace them. **Outdoor Unit (Heat Pump on Side of House):** * Observed the outdoor unit to be in fair condition. * Verified the outdoor coil is clean and in fair condition. **Electrical Components:** * Verified proper operation and specs for: * Blower Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Electrical Wiring **System Components:** * Inspected and confirmed proper operation of: * Blower Wheel * Primary Drain Pan * Electrical Wires Secured * Ductwork **System Readings & Adjustments:**

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. * **Indoor Unit (Air Handler in Closet):** * Replaced the pleated 1" filter (size 17x22x1) using the customer's spare filters. * Confirmed the indoor coil is clean. * **Outdoor Unit (Heat Pump):** * Confirmed the outdoor coil is clean. * **Electrical Components (Tested and Working):** * Verified proper operation and amperage of the blower motor, heat strip kit, condenser fan motor, compressor, fan run capacitor, blower run capacitor, compressor run capacitor, contactor, and electrical wiring. * **Inspected Components (Good Condition):** * Confirmed the blower wheel, primary drain pan, and electrical wires are secured and in good working order. * **Condensate Drain System:** * Cleared the drain line and cleaned out the primary pan. * Tested the safety switch. * Verified the drain line is strapped. * **Measurements:** * Recorded a

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler):** * Located in closet, servicing the whole home. * Replaced the pleated 1" filter. * Filter sizes: 12x12x1, 16x25x1, 22x22x1. * Observed the indoor coil to be in fair condition. **Outdoor Unit (Heat Pump):** * Located on the side of the house. * Observed the outdoor coil to be in fair condition. **Electrical Components:** * Tested and inspected the following components, all operating within manufacturer's specifications: * Blower Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Blower Run Capacitor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Electrical Wiring **System Components:** * Inspected the following components and confirmed they are in good condition and working properly: * Blower Wheel * Secondary Drain Pan * Primary Drain Pan * E

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Garage):** * Observed the overall condition as good. * Noted the filter size is 20x25x4. * Observed the indoor coil in good condition. **Outdoor Unit (Heat Pump on Side of House):** * Cleaned the outdoor coil, noting its fair condition. **Electrical Components:** * Verified electrical wiring is working properly within manufacturer's specifications. **System Components (Inspected and in Good Condition):** * Confirmed the blower wheel is in good condition. * Verified the primary drain pan is in good condition. * Verified the secondary drain pan is in good condition. * Verified electrical wires are secured. **Condensate Drain System:** * Cleared the drain line. * Cleaned out the primary pan. * Cleaned out the secondary pan. * Tested the safety switch. * Confirmed the drain line is strapped. **Temperature Readings:** * Recorded a re

Today I performed a winter time tune up on your Bensons hvac equipment.Testing system operations, component amperages, capacitor ratings, verified the up light is operational, cleared the drain line , washed the filter, cleaned the condenser coil , and removed leaves and debris from inside the unit.Your system is working properly at this time. Thank you for your business

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler):** * Verified the unit is a Mini Split Indoor Unit located in a closet, servicing the whole home. * Confirmed the filter is a pleated 1", sized 20x20x1, and in fair condition. Customer will replace the filter themselves. * Observed the indoor coil to be in fair and clean condition. **Outdoor Unit (Heat Pump):** * Verified the unit is a Mini Split Condenser located in the back yard. * Observed the outdoor coil to be in fair and clean condition. * Tested and confirmed the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring are working properly within manufacturer specifications. * Inspected and confirmed the blower wheel, primary drain pan, and electrical wires are secured and in good working condition. **Condensate Drain System:** * Cleared the drain line and clea

Customer was experiencing loud airflow. Found the filter to be dirty causing the unit to work harder to pull air through the filter. When I removed the filter I saw a plastic tub fall which leads me to believe the thumping may have been caused by the plastic tub bouncing around due to the airflow. Thank you for your business.

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Attic):** * Observed the overall condition as fair. * Confirmed the unit services the upstairs area. * Replaced the pleated 1" filter (size 18x18x1) using the customer's spare filters. * Verified the indoor coil is clean and in fair condition. **Outdoor Unit (Heat Pump on Side of House):** * Observed the outdoor coil is clean and in fair condition. **Electrical Components:** * Tested and confirmed proper operation of the blower motor, heat strip kit, compressor, contactor, and electrical wiring within manufacturer's specifications. **System Components:** * Inspected and confirmed the blower wheel, primary drain pan, electrical wires, and ductwork are in good working condition. **Condensate Drain System:** * Cleared the drain line. * Cleaned out the primary pan. * Tested the safety switch. * Confirmed the drain line is strapped. **Tempera

Today I performed a winter time tune up on your Goodman Heat-pump package unit , your system is working properly at this time however I did find that the dual run capacitor is reading below manufacture specifications and the single pole contactor is extremely pitted on the contacts , both items covered under 10 yr P&L warranty , I will order the parts and return to install. Tallahassee Fl (model#GPH1448H41 ,Serial#1909143622)

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Attic):** * Replaced the 20x20x5 pleated filter. * Confirmed the indoor coil is clean and in fair condition. **Outdoor Unit (Heat Pump on Side of House):** * Confirmed the outdoor coil is clean and in fair condition. * Verified proper operation of the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. * Confirmed the blower wheel, electrical wires, primary drain pan, and ductwork are in good condition. **System Checks:** * Cleared the condensate drain line and cleaned out the primary pan. * Tested the safety switch. * Confirmed the drain line is strapped. * Measured a return air temperature of 73.0°F and a supply air temperature of 90.0°F. **Additional Actions:** * Dusted the thermostat. * Restored power to the units. * Checked the batteries and tes

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Attic/Garage):** * Verified the unit services the whole home. * Checked the pleated 16x25x4 filter (2-6" type); it's in good condition. * Confirmed the indoor coil is clean and in good condition. **Outdoor Unit (Heat Pump on Side of House):** * Confirmed the outdoor coil is clean and in good condition. **Electrical Components (Tested and Working):** * Verified proper operation and amperage of: * Blower Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Electrical Wiring **Component Inspection (Good Condition):** * Confirmed the following are in good condition and working properly: * Blower Wheel * Primary Drain Pan * Electrical Wires Secured * Ductwork **System Readings & Adjustments:** * Return air temperatu

Today I performed a routine maintenance on your heat pump split system. I checked all electrical connections on both indoor and outdoor equipment, checked your air filters, flushed the drain line, check your capacitor ratings, and then make sure your system came back on and operated properly before leaving. Your system is operating properly at this time .

The customer recently installed a Wi-Fi thermostat afterwards the system was not cooling properly. Upon further inspection, I found the thermostat was never programmed for a heat pump. After to reprogramming the thermostat, I tested your system operations. Your system is both heating and cooling properly at this time. The customer also wanted to sign up for a silver level maintenance. We went ahead and took care of that as well. The system is on and operating properly at this time

Upon arrival, I found the customer’s heat pump split system not working properly due to a low refrigerant charge. I performed an electronic leak search to find the evaporator coil leaking while performing the leak search. I also noticed the indoor blower motor to be running constantly with no call for it. After further inspecting that I found a bad indoor blower control board. I sent an estimate via email to the customer to replace the evaporator coil and indoor blower control board. The customer approved the estimate. As of now, it is scheduled for first call Thursday morning to be installed. We should be here between 830 and 10 o’clock in the morning to get started. We will call when we are on the way. I left the system, how it was when I arrived.

Today I arrived on site and performed a winter tune-up on the system. Here's a summary of the work completed: * **Air Handler (Garage, Attic):** * Verified the overall condition as good. * Confirmed the unit services the whole home. * **Filtration:** * Checked the 20x20x5 pleated filter. * Replaced the filter; the customer requested additional filters for a charge. * **Indoor Coil:** * Verified the indoor coil is in good, clean condition. * **Heat Pump (Side of House):** * Verified the outdoor coil is in good, clean condition. * Cleaned the outdoor coil. * **Electrical Components (Tested and Working):** * Blower Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Blower Run Capacitor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Defrost Control Board * Electrical Wiring * **System Components (Inspected and Working):** * Blower Wheel *

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. Indoor Unit (Air Handler in Attic/Garage): Replaced the 20x20x4 pleated filter with a spare provided by the customer. Confirmed the indoor coil is clean and in fair condition. Outdoor Unit (Heat Pump in Back Yard): Verified the outdoor coil is clean and in good condition. Tested and inspected the following electrical components, all operating within manufacturer's specifications: Blower Motor Heat Strip Kit Condenser Fan Motor Compressor Compressor Run Capacitor Fan Run Capacitor Compressor Start Capacitor Contactor Electrical Wiring Inspected the following components, all in good working order: Blower Wheel Primary Drain Pan Electrical Wires Secured Secondary Drain Pan System Checks: Return air temperature: 71.0°F. Supply air temperature: 126.0°F. Cleared the condensate drain line and cleaned out the primary pan. Tested the safety switch. Confirmed the drain line is strapped. Additional Actions:

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. Here's a summary of the work completed: Indoor Unit (Air Handler in Closet): Verified the indoor unit is in good condition. Confirmed the indoor coil is clean and in good condition. Replaced the pleated 1" filter (24x30x1). Customer provided spare filters. Confirmed the blower wheel, primary drain pan, and electrical wires are secured and in good condition. Outdoor Unit (Heat Pump on Side of House): Verified the outdoor unit is in good condition. Confirmed the outdoor coil is clean and in good condition. Tested and inspected the following electrical components, all operating within manufacturer's specifications: Blower Motor Condenser Fan Motor Compressor Compressor Run Capacitor Fan Run Capacitor Compressor Start Capacitor Contactor Electrical Wiring System Checks: Cleared the condensate drain line and cleaned out the primary pan. Tested the safety switch on the condensate drain system. Confirme

Performed a winter time tune up on a ICP Heat Pump View visual findings from this job here - https://visionshare.xoi.io/?id=XA-A243-D5A658BF8B0D49CFB8B50E2A33DDDAB7

Today I performed a wintertime tuneup on your air conditioning system in Crawfordville FL. Everything is working properly at this time.

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Attic):** * Confirmed overall equipment condition is good. * Observed the indoor coil is clean and in good condition. **Outdoor Unit (Heat Pump on Side of House):** * Observed the outdoor coil is clean and in good condition. **Electrical Components (Tested and Working):** * Verified proper operation of the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. **Inspected Components (Good Condition):** * Confirmed the blower wheel, primary drain pan, and electrical wires are secured and in good condition. **Airflow and Temperature:** * Measured a return air temperature of 73.0°F and a supply air temperature of 121.0°F. **Condensate Drain System:** * Cleared the drain line and cleaned out the primary pan. * Tested the safety switch to ensure proper function.