Crawfordville, FL HVAC Company

Customer said that the unit was blowing out hot air. Found the reversing valve to not be engaging into cooling mode. Checked thermostat and everything was set up correctly. After turning thermostat back on the reversing valve engaged just fine. Checked operation of unit and it shut down after about 10 minutes, this was most likely due to a power surge that seems to of reset the cable as well. Unit ran for about 10 minutes before shutting off again. Found filter to be dirty so I replaced the filter with a customer provided one. Unit turned off again with the thermostat satisfying at 75 before jumping up to 77 shortly after. This is most likely caused by the vent in the bathroom next to the thermostat to be putting out a lot of air making the thermostat read a touch lower. Turned thermostat way down to watch it run for 20 minutes with no issue, when I turned the thermostat back off the temperature did not raise shortly after. Thank you for your business.

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Attic Closet):** * Replaced the 16x20x5 pleated filter with a spare provided by the customer. * Confirmed the indoor coil is in fair and clean condition. **Outdoor Unit (Side of House - Heat Pump):** * Verified the outdoor coil is in fair and clean condition. * Tested and confirmed proper operation of the blower motor, heat strip kit, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, and contactor. * Confirmed electrical wiring is working properly within manufacturer's specifications. * Inspected and confirmed the blower wheel, secondary drain pan, primary drain pan, electrical wires, and ductwork are in good condition and working properly. **System Performance:** * Measured a return air temperature of 75.0°F and a supply air temperature of 132.0°F. * Cleared the condensate drain line.

Today I arrived on site and performed a winter time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Closet):** * Observed the indoor unit to be in fair condition. * Confirmed the indoor coil is clean and in fair condition. * Noted the filter size is 20x30, pleated 1". Customer has spare filters and will replace them. **Outdoor Unit (Heat Pump on Side of House):** * Observed the outdoor unit to be in fair condition. * Confirmed the outdoor coil is clean and in fair condition. **Electrical Components:** * Tested and inspected the blower motor, heat strip kit, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, compressor start capacitor, contactor, and electrical wiring; all are working properly within manufacturer's specifications. **Component Inspection:** * Inspected the blower wheel, primary drain pan, electrical wires, and ductwork; all are in good condition and working properly. **System Readin

Today, I arrived on site to perform a tune-up on the HVAC system. Overall Equipment Condition: * Condition rated as fair. Indoor Unit Details: * Located in the closet. * Serves the whole home. * Antimicrobial filter replaced today, size 20x20. Indoor Coil Condition: * Rated as fair. Outdoor Unit Details: * Located in the back yard. * Outdoor coil condition rated as fair. Electrical Component Testing: * Blower Motor, Blower Run Capacitor, Compressor, Compressor Run Capacitor, Fan Run Capacitor, Contactor, and Electrical Wiring tested and working properly within manufacturer specs. Component Inspections: * Blower Wheel, Primary Drain Pan, and Electrical Wires secured in good condition. * No components found in poor condition. Additional Testing: * No carbon monoxide detected. Temperature Readings: * Return Air Temperature: 77.0°F. * Supply Air Temperature: 52.1°F. Condensate Drain System Maintenance: * Cleared drain line. * Cleaned out primary pan. * Tested safety switch. Additional Note

10/14/2025- I arrived on site and replaced the faulty blower motor with OEM parts. After installation of the new equipment I tested the new motor in every mode of operation and have confirmed that the unit is now functioning properly. I then tested the unit under load and have verified that this unit is functioning and cooling properly with a 20 degree temperature split. All components are functioning within spec and this unit is working properly at the time of service. The customer has paid $900.00 is cash and the remaining $12.71 with card. Thank you for your business.

The customer approved an estimate I sent out after the maintenance last week to replace a bad damper actuator for the zone system. I have to replacing the zone damper actuator. I tested the damper in the system operations. Your zone system is operating properly at this time .

Upon arrival, I found the customer’s Dyke and split system not cooling properly due to the condenser being tripped on a hard lockout at the Copeland scroll protector. I checked the capacitor in the system operations and everything checked out good when I reset the Copeland school protector the system came on and started cooling properly. I then checked the pressures and everything checked out good to go in. The system dropped from 78° and was satisfied at 76° before I could leave. Your system is operating properly at this time

Today I performed a fall tuneup on your Amana heat pump unit. Everything is working properly at this time. Thank you for your business. Crawfordville FL

Today, I arrived on site to perform a winter maintenance on the HVAC equipment. Equipment Condition: * Overall equipment condition noted as fair. * Indoor unit located in a closet, servicing the whole home. * Outdoor unit situated on the side of the house, condition fair and clean. Filtration: * Replaced pleated 1" filter today. * Filter size: 4) 12x24x1. Indoor Coil: * Condition assessed as fair. * Recommended duct cleaning for optimal performance. Electrical Components: * Blower motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring tested and confirmed to be working properly within manufacturer specs. Components in Good Condition: * Blower wheel, primary drain pan, electrical wires secured, and ductwork inspected and functioning well. Temperature Readings: * Return air temperature recorded at 70.0 degrees Fahrenheit. * Supply air temperature measured at 110.0 degrees Fahrenheit. Condensate Drain System: * Cleared the drain line and cleaned b

Today I performed a fall tuneup on your Tempstar heat pump unit. I tested electrical components, checked the filter, cleared and primed the drain line, and ran the system in heat mode. The system is heating and cooling properly at this time. Thank you for your business. Crawfordville FL

Today I performed a fall tuneup on your Goodman heat pump unit. I tested electrical components, cleared the drain line, replaced the filter, and checked pressures. I found the system somewhat low on refrigerant and I found a leak in the evaporator coil. I have given an estimate to replace the coil. The system is cooling and heating properly in the meantime.

Today I arrived on site and performed a winter tune-up. Here's a summary of the work completed: **Indoor Unit (Package Unit):** * Noted the overall equipment condition as fair. * Brush cleaned the indoor coil, which was in good condition. * Hosed down the evaporator coil. * Checked the antimicrobial filter; customer will provide their own replacement filters. **Outdoor Unit (Heat Pump, Package Unit):** * Noted the outdoor coil condition as fair and cleaned it. **Electrical Components:** * Tested and confirmed proper operation of the blower motor, heat strip kit, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. * Inspected and confirmed good condition of the blower wheel, secured electrical wires, primary drain pan, and secondary drain pan. **System Checks:** * Cleared the drain line and cleaned out the primary pan in the condensate drain system. * Measured a return air temperature of 74.0°F and a s

Today I performed a routine maintenance on your HVAC equipment. I checked all electrical connections on both indoor and outdoor equipment. Washed your filters flushed your drain lines checked your capacitor ratings and then check system operations after the maintenance. During the maintenance I noticed the upstairs zone was stuck open, which it explained why it’s so cold up there. I will go back in the history and see when we last replaced them and get an estimate emailed over ASAP if they’re no longer under warranty to replaced the zone damper actuator. Other than that, everything else is operating properly at this time .

Upon arrival I found the customer’s secondary pan had been filling up with water since the end of July. We were just out at the end of July for the same thing and the customers had to empty the drain pan twice since. After further inspecting the system, I found where the primary drain line comes out of the air handler cabinet. It had popped out of the coupling and was draining out of the armor flex directly into the secondary pan. I was able to get the drain back in the coupling. I flushed the drain line and then let the system run until it started draining. Your system is cooling/draining properly at this time

Today I arrived on site and performed a winter tune-up on the system. Here's a summary of the work completed: **Indoor Unit (Air Handler - Garage):** * Checked the pleated 20x25 filter. * Observed the indoor coil in fair condition. **Outdoor Unit (Heat Pump - Side of House):** * Cleaned the outdoor coil, which was in fair condition. **Electrical Components:** * Tested and confirmed proper operation of the blower motor, condenser fan motor, compressor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. **System Components:** * Inspected and confirmed good condition of the blower wheel, secured electrical wires, primary drain pan, and secondary drain pan. **Measurements & Adjustments:** * Measured a return air temperature of 74.0°F and a supply air temperature of 106.0°F. * Cleared the condensate drain line and cleaned out the primary pan. * Tested the safety switch. * Restored power to the units. Tallahassee Fl View my findings fr

Today I arrived on site and performed a winter time tune up on your system, and it is working properly at this time. **Indoor Unit (Air Handler in Attic):** * Checked and washed the 20x20 washable filter. * Confirmed the indoor coil is in good, clean condition. **Outdoor Unit (Heat Pump in Back Yard):** * Confirmed the outdoor coil is in good, clean condition and cleaned it. * Tested and inspected the following electrical components, all working within manufacturer's specs: * Blower Motor * Heat Strip Kit * Condenser Fan Motor * Compressor * Blower Run Capacitor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Defrost Control Board * Electrical Wiring * Inspected the following components, all in good working condition: * Blower Wheel * Ductwork * Electrical Wires Secured * Primary Drain Pan * Secondary Drain Pan **Condensate Drain System:** * Cleared the drain line. *

Upon arrival, I found the customer’s water source heat pump, not cooling properly due to a clogged drain line, causing the water to back up into the primary pan causing the safety float switch to kill the low-voltage call for the compressor. I sent an estimate to flush the drain line. The estimate was approved. After flushing the drain line I turned the system back on and made sure the system came on and started cooling properly. Your system is cooling properly at this time

Today I arrived on site and performed a winter time tune up on your system. The overall equipment condition is good. **Indoor Unit (Air Handler - Garage, Attic):** * Confirmed the indoor coil is clean and in good condition. * Checked the pleated 1" filter; the customer has spare filters and will replace it themselves. **Outdoor Unit (Heat Pump - Side of House):** * Verified the outdoor coil is clean and in good condition; cleaned it today. **Electrical Components:** * Tested and confirmed the following components are working properly: blower motor, electrical wiring, defrost control board, contactor, blower run capacitor, compressor, condenser fan motor, and heat strip kit. * Replaced the compressor run capacitor and condenser fan motor run capacitor with a turbo 200. **System Components:** * Inspected and confirmed the blower wheel, ductwork, secured electrical wires, primary drain pan, and secondary drain pan are in good condition and working properly. **Condensa

Today I arrived on site and performed a summer tune-up. The system is currently working properly. **Indoor Unit (Air Handler):** * Located in the attic closet. * Verified the indoor coil is in good condition. * Replaced the pleated 20x25x4 filter. * Confirmed the customer wants the technician to provide additional filters for a charge, as they do not have spares. **Outdoor Unit (Heat Pump):** * Located in the backyard. * Verified the outdoor coil is in good condition. **Electrical Components:** * Tested and confirmed the following components are working within manufacturer's specifications: blower motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, and electrical wiring. **System Components:** * Inspected and confirmed the following components are in good condition and working properly: blower wheel, heat exchanger, secondary drain pan, primary drain pan, secured electrical wires, and ductwork. **System Performance:*

Today I arrived on site and performed a summer time tune up on your system. It is currently working properly. **Indoor Unit (Air Handler - Attic, Garage):** * Indoor coil condition: Good, Clean. * Filtration: * Replaced Pleated 1" filter (20x25x1 & 16x20x1). * Customer provided spare filters. **Outdoor Unit (Heat Pump - Side of House):** * Outdoor coil condition: Good. **Electrical Components (Tested and Working):** * Blower Motor * Compressor * Blower Run Capacitor * Compressor Run Capacitor * Fan Run Capacitor * Contactor * Defrost Control Board * Electrical Wiring **System Components (Inspected and in Good Condition):** * Blower Wheel * Heat Exchanger * Secondary Drain Pan * Primary Drain Pan * Electrical Wires Secured * Ductwork **Condensate Drain System:** * Cleared drain line. * Cleaned out primary pan. * Cleaned out secondary pan. **Measurements:** * Return Air Temperature: 77.0 Degrees Fahrenheit. * Supply Air

Today I arrived on site and performed a summer time maintenance on your HVAC equipment. **Indoor Unit (Air Handler in Garage/Attic):** * Replaced the existing 20x25x4 pleated filter with a spare provided by the customer. * Confirmed the indoor coil is in fair, clean condition. **Outdoor Unit (Heat Pump on Side of House):** * Verified the outdoor coil is in fair, clean condition. * Tested and confirmed the following electrical components are working properly: Blower Motor, Condenser Fan Motor, Compressor, Blower Run Capacitor, Compressor Run Capacitor, Fan Run Capacitor, Compressor Start Capacitor, Contactor, and Electrical Wiring. * Inspected and confirmed the following components are in good condition: Blower Wheel, Primary Drain Pan, Electrical Wires Secured, Ductwork, and Secondary Drain Pan. **System Performance:** * Measured a return air temperature of 72.0°F and a supply air temperature of 55.0°F. * Cleared the condensate drain line. * Cleaned out the primar

Summary: **Job Summary** Today, I arrived on site to perform summer maintenance on the HVAC equipment. **Overall Equipment Condition** - Equipment condition is good. **Indoor Unit Details** - Location: Garage, Attic - Type: Air Handler - Filtration: Pleated 2-6", replaced today; customer will provide their own filters. - Filter Size: 20x25 - Condition of Indoor Coil: Good, clean. **Outdoor Unit Details** - Location: Back Yard - Type: Heat Pump - Condition of Outdoor Coil: Good, clean. **Electrical Components Tested** - All components tested and functioning within manufacturer specifications: - Blower Motor - Condenser Fan Motor - Compressor - Compressor Run Capacitor - Fan Run Capacitor - Contactor - Defrost Control Board - Electrical Wiring **Inspections** - Components in good condition: - Blower Wheel - Electrical Wires Secured - Primary Drain Pan - Secondary Drain Pan - No components found in poor condition. **Temperature Readings** - Return Air Temperature: 75.0°F - Supply Air Temp

Today, I arrived on site to perform a comprehensive summer maintenance on the HVAC system. Equipment Condition: * Overall condition rated as good. * Indoor unit located in the garage attic, serving the whole home. Filtration: * Checked and replaced pleated filters (20x20x5). * Customer requested additional filters for a charge. Indoor Coil: * Condition is good and clean. Outdoor Unit: * Heat pump located on the side of the house. * Outdoor coil is also in good condition and cleaned today. Electrical Components: * All tested components, including blower motor, condenser fan motor, compressor, and capacitors, are functioning within manufacturer specifications. * No issues found in electrical components. System Inspections: * Blower wheel, primary and secondary drain pans, and electrical wires are in good condition. * No components found in poor condition. Temperature Readings: * Return air temperature is at 72.0 degrees Fahrenheit. * Supply air temperature measured at 46.0 degrees Fahren

Performed a tune up on the equipment. Testing system operations, component amperage’s, capacitor ratings, cleared the drain line, checked the filter, tested the thermostat and condenser. The system is working properly at this time.

Today I arrived on site and performed a summer tune-up. **Indoor Unit (Garage, Attic):** * Whole home unit serviced. * Filter: * Washed washable filter. * Checked pleated 20x25 filter. * Indoor coil condition: Fair. **Outdoor Unit (Side of House):** * Outdoor coil condition: Fair. **Electrical Components:** * Tested and inspected: Blower motor, condenser fan motor, compressor, blower run capacitor, compressor run capacitor, fan run capacitor, contactor, compressor start capacitor, and electrical wiring; all working within manufacturer's specifications. **System Components:** * Inspected: Blower wheel, secondary drain pan, primary drain pan, and electrical wires; all in good working condition. **System Testing & Adjustments:** * Return air temperature: 78.0°F. * Supply air temperature: 60.0°F. * Condensate drain system: * Cleared drain line. * Cleaned primary pan. * Cleaned secondary pan. * Tested safety switch. **Final S